Campbell CR510 Manual del operador descargar pdf (Pagina 206)

TABLE DATA ADDENDUM

AD-6

This is a blank page.

1 2 ... 201 202 203 204 205 206 207 208 209 210 211 ... 263 264

CR510 DATALOGGER 1
OPERATOR'S MANUAL 1
WARRANTY AND ASSISTANCE 3
TABLE OF CONTENTS 5
DATA RETRIEVAL/COMMUNICATION 6
PROGRAM EXAMPLES 6
INSTRUCTIONS 7
INSTALLATION 7
APPENDICES 8
FEATURES OF CR510 9
This is a blank page 10
SELECTED OPERATING DETAILS 11
CAUTIONARY NOTES 12
CR510 DATALOGGER OVERVIEW 13
OV2. MEMORY AND PROGRAMMING 15
CONCEPTS 15
OV4. PROGRAMMING THE CR510 21
CR510 OVERVIEW 30
ARRAYS, AND MEMORY POINTERS 45
3.1 PARAMETER DATA TYPES 49
3.2 REPETITIONS 49
3.4 INDEXING INPUT LOCATIONS 49
3.5 VOLTAGE RANGE AND 50
OVERRANGE DETECTION 50
3.6 OUTPUT PROCESSING 50
PROGRAM CONTROL 51
3.8 PROGRAM CONTROL LOGICAL 52
CONSTRUCTIONS 52
3.9 INSTRUCTION MEMORY AND 55
EXECUTION TIME 55
3.10 ERROR CODES 59
4.1 ON-LINE DATA TRANSFER 61
INSTRUCTION 96 61
4.4 STORAGE MODULE 64
5.1 TELECOMMUNICATIONS 67
COMMANDS 67
6.1 PIN DESCRIPTION 71
6.2 ENABLING AND ADDRESSING 72
PERIPHERALS 72
6.3 RING INTERRUPTS 73
6.6 SYNCHRONOUS DEVICE 74
COMMUNICATION 74
6.7 MODEM/TERMINAL AND 75
COMPUTER REQUIREMENTS 75
7.1 SINGLE ENDED VOLTAGE 79
107 TEMPERATURE PROBE 79
7.2 DIFFERENTIAL VOLTAGE 79
MEASUREMENT 79
7.4 ANEMOMETER WITH 81
PHOTOCHOPPER OUTPUT 81
LONG LEADS 82
FULL BRIDGE 86
7.12 NONLINEAR THERMISTOR IN 90
HALF BRIDGE 90
CR510 & AVW1 93
12 V or 5 V 94
7.14 4 TO 20 MA SENSOR USING 95
CURS100 TERMINAL INPUT 95
SYNCHED TO REAL TIME 99
PORTS (RAIN GAGE) 99
8.5 CONVERTING 0-360 WIND 100
DIRECTION OUTPUT TO 0-540 FOR 100
STRIP CHART 100
- SAVING DATA PRIOR TO EVENT 101
zero yields 110
SEQUENCE 145
13.2 SINGLE-ENDED AND 146
DIFFERENTIAL VOLTAGE 146
MEASUREMENTS 146
LENGTH ON THE SIGNAL SETTLING 147
13.4 BRIDGE RESISTANCE 156
13.5 RESISTANCE MEASUREMENTS 160
REQUIRING AC EXCITATION 160
13.6 CALIBRATION PROCESS 161
14.1 PROTECTION FROM THE 163
ENVIRONMENT 163
14.2 POWER REQUIREMENTS 163
SUPPLIES 164
12V ALKALINE BATTERY PACK 165
DESI PAK 166
14.7 GROUNDING 168
14.8 TERMINAL STRIP 169
FOR SWITCHING RELAYS 169
14.10 MAINTENANCE 171
APPENDIX A. GLOSSARY 173
B.1 TELECOMMUNICATIONS 177
COMMAND WITH BINARY 177
RESPONSES 177
B.2 FINAL STORAGE FORMAT 179
APPENDIX C. ASCII TABLE 183
D.1 INTRODUCTION 185
D.2 EXAMPLE PHONE CALLBACK 185
PROGRAM BASED ON A CONDITION 185
AND IT’S COMPUTER SETUP 186
APPENDIX E 189
E.4 REMOTE DATALOGGER 191
PROGRAMMING 191
F.1 TERMINOLOGY 193
F.2 COMMUNICATIONS AND 193
COMPATIBILITY 193
F.3 MORE ON MODBUS 194
AND CR23X MANUALS 199
AD1 Major Differences 201
AD3.1 Programming changes 202
Section 12 205
TABLE DATA ADDENDUM 206
OV4. PROGRAMMING THE CR10X 207
OV5. PROGRAMMING EXAMPLES 209
32 converts the 211
03:P84 Data Table Instruction 212
OV6. DATA RETRIEVAL OPTIONS 213
DATALOGGER 214
COMPUTER 214
SECTION 1. FUNCTIONAL MODES 215
STATUS - ∗B 217
1.7 ∗C MODE -- SECURITY 217
1.8 ∗D MODE – TRANSFER 217
PROGRAMS, GENERAL SETTINGS 217
1.9 *9 DATA TABLES SIZES 221
2.1 FINAL STORAGE AND DATA 223
2.2 DATA OUTPUT FORMAT AND 225
RANGE LIMITS 225
KEYBOARD/DISPLAY *7 MODE 225
8.1 COMPUTATION OF RUNNING 229
8.2 RAINFALL INTENSITY 230
8.3 USING CONTROL PORTS AND 231
LOOP TO RUN AM416 MULTIPLEXER 231
TO COUNT SWITCH CLOSURES 233
(RAIN GAGE) 233
8.5 SDM-A04 ANALOG OUTPUT 234
MULTIPLEXER TO STRIP CHART 234
Section 12. Program Control 243
Instructions 243
Security 248
Remote Location/Coil/Register 248
Remote Location 249
Local Location 249
Send Message (P192) 250
Message Type 251
Number of Remotes 252
First Remote Address 252
Time into Transmit Interval 252
Transmit Interval 252
Swath to Receive 253
Seconds Until Transmit (P194) 254
Swath to Receive From Master 256
Swath to Send 256
First Location to Send 256
Force Route (P197) 257
Set Setting (P198) 257
Result Location 258
Beacon Intervals 259
Neighbor Filter 260
LIST OF TABLES 261
LIST OF FIGURES 263

Comentarios a estos manuales

Sin comentarios

Campbell CR510 Manual del operador Pagina 206

Comentarios a estos manuales

Relacionado con productos y manuales para De medición, control y control Campbell CR510